Search results for query: *

Any of you guys or gals running a 28/12.5/15 street Radial on a 12 inch rim? I am looking at some MT S/R 28s and need to know the section on a 12 inch wheel.

Have any of you guys installed a tire recommended for a 10 inch rim onto a 12 inch rim?

Is it ok to use a chrome 4 pin in place of an orange 4 pin ecu? orange one will no longer start the car,no spark. Used chrome one will. Just dont want to mess anything up.

If a person doesnt have a full 12 volts going to an electronic oil pressure sending unit, will the pressure readings be off a little or a lot? Or does it make any difference if the voltage is a little low?

What are yall using in regards to sound deadner ?

What type of oil pressure guage is better? are you using? Electrical? or Mechanical? I have an electrical at present but not real sure of its accuracy.I am thinking of going mechanical? Not sure though if its worth the effort.

What would keep a freshly rebuilt 727 from shifting into third gear? I have a Lokar kickdown cable on it and it seems to be set correct. Is there more than on way to connect the factory linkage? I want to be sure I have done my part correctly before I call the transmission shop that freshed it...

Any of you guys or galls running a panhard bar? I am thinking about doing so on my 72 Dart,so as to keep the tires away from the fenders.They are really close and rub when I turn. I have about 1/2 inch clearance on either side of the rear tire. I am about to rebuild the rear leaf spring bushings...

Does any one know if one of the new adjustable anti- sway bars from Helwig [6907]{ the one which mounts on the frame rails] will fit a Dart with a narrowed 9 inch?As regards the front sway bar 5906 [Helwig] will it adapt to a 72 Dart that did not have a bar installed from the factory?

Any of yall have a 72 Dart Swinger 1/18 scale Diecast car that you have bought? I am wanting one to replicate to look like my real one. I cant find one anywhere in the world. Any help would be appreciated. Dale

What rear shocks did you guys use after you minitubbed your A body? I put the originals back on after minitubbing my 72Dart, and they bottom out after about 2 inches of down travel which I knew they would when I installed them.Went to Oreillys,but they were no help at all.

After reinstalling engine and accessories- minus a/c- I am in a pickle as to placement of powersteering pump belt. Pulley seems to line up inbetween double pulleys on crank pulley.Does the ps belt run off of furtherst pully out groove or second one in from front? I replaced the leaking ps pump...

Have any of yall used POR 15 on a body panel? I thought I had the rust on my roof killed out before I painted it,but not so as it is coming back and pushing off my 2 year old paint in a few spots. The Dart had a vinyl top before but I got rid of it. I am going to have to repaint and was...

I was wondering if an electric fuel pump always makes a sound ? or will they quiten down so as to not hear them?

I installed a new intermediate shaft in newly rebuilt 360 when I put dist. in. I thought I had everything set up properly,I guess not though. If i got the intermediate shaft off 1 tooth, how bad would that mess me up? I installed it pointing at #1 with # 1 on tdc, or so I thought. Will I have to...

Just tried to start newly rebuilt 360 with rebuilt 727. Will the nuetral safety switch not allow the car to start, by not activating the starter relay? I can jump across relay and spin motor. Also I have put trans. fluid in but I am still able to roll the car around with the colum shift in...

Trying to fire off new 360. Coil is getting hot! Car wont start. I installed all new ignition. Dist. coil, and orange box. why would coil get so hot?

I have a 727 trans and a 9 inch rear. I have the piece that goes into the transmission and the drive shaft that came with the 9 inch. I am going to have shaft shortened and reuse it .What combination u-joint do I need to be able to work with the 727 slip yoke?

Going to purchase a new alternator. Some show internal regulator some say external. My 72 Dart has a regulator mounted on firewall.If I get an internal reg., what do I do with the wiring that went to reg. on firewall? Anything ? I dont know much about eletrical, I just want to do it right.

What wires would need to be upgraded in order to run a 120 amp alt.? Would reg. need upgraded as well?

I am ready to purchase a kickdown cable set up. What have yall found to work the best? easiest to install?Lokar is about half the price of the Bouchillon,but if its better ,easier,it may well be worth it. what do you guys think?

Have any of yall put ignition box inside the car. Also I have a 120 amp alt. which came with the engine off a 350 series van.Will the 120 amp alternator cause problems in my 72 Dart? Seems as though I read that someone melted some wiring with a 100 amp !!

I am trying to get 360 set down on the kframe in my 72 Dart.I have one thick rubber pad and one thin rubber pad.I have the thin one on driver side and the thick one on the passenger side,but the engine doesnt seem to want to set down on the frame on the passenger side. Can anyone tell me how...

I tried to install my 360 into my 72 Dart this evening. I have a Milidon 8 qt. oil pan [ 30940] on it,and I cant seem to get it to clear the k frame is it a really close fit?.I also need some help with motor mounts. Does anyone have any photos of correctly installed motor mounts.I bought a mt...

Can a person install a set of Dougs 453 with them already bolted to engine? Do I need to remove the starter , or can it stay bolted up? The engine is going in fromthetop with trans connected. Any suggestions will be appreciated.

In my 72 Dart I have replaced the 318 engine which had a points type distributor, with an 89 360 engine that has a breakerless type dist.. The old dist. has one wire coming out of it, and the one in the 360 has a 3 wire connector. Is there a way to make the breakerless dist. work with the...

The Air gap intake has an extra water access port in the rear right hand corner. Can a person use it for a heater hose connection? If so it would mean less stuff coming to the front.Has anyone tried this?

Some where on this site yall were talking bout some really good sound deadner and heat barrier. There was a link to a fellows site that does car stereo work who sells it by the 50 ft. roll. Where did I read about that stuff?? It was priced right as well.

I was wondering what thermostat I need to go on my airgap intake. The one I got from summit which is a Milidon high flow will almost fall completly into the intake!! I just read on the Summit how to install page on the intake, that I need the early style water neck.It didnt say anything about a...

I spoke with a guy at Mancini about Uncoated TTIs for my Dart .He called TTI and was told that they would cost only $10 less than chrome ones. I really need, or at least I think I need uncoated for now.I was going to remove and have them coated later. But maybe I will go ahead and go ceramic...