72 duster resto

[72smallairparticler]

Had a full saturday morning to work on the car so got a few more things wrapped up:

• 8.8 backing plates, emergency brake, rotors, pads, calipers all installed
• painted up some more engine bay
• testing out some variant of flat black engine paint on my valve covers, but not sure I like the idea of keeping them clean! lol.

I also thought it would be cool to paint the covers with F3 sherwood and then touch up the lettering with orange, but that sounds like a project for later.

On the engine Brian said it's not a big deal with adjustable rockers so just gonna install the valvetrain, spec the pushrod lengths, grab the right set and make sure the pushrod ports in the heads don't need any clearancing before I torque everything down. I'm stuck waiting on a lost set of arp headbolt washers that probably got lost when I last cleaned up my workarea. Hate that. Oh well. Grabbed some gear oil for the rear end so nothing stopping me from setting pinion angle and welding on the spring perches next. Can't wait to drive this thing.

I do have one question - for those who have converted column shifts to floor shifts is this an easy task? I dont NEED to do it (yet), but I was reading the instructions on my Summit brand header installation and it mentions potentially reconfiguring the shift linkage if clearance is an issue. I knew header installation would be a PITA at some point but trying to get ahead of any headaches down the way if possible.

 

[mygasser]

now you've sanded the ribs n lettering on the valve covers they just need some clear lacquer to keep them easy clean. other than that it's all looking good so far
neil.

 

[junkyardhero]

bay looks good. what paint did you use?
(asking for a friend)

 

[72smallairparticler]

bay looks good. what paint did you use?
(asking for a friend)

Touchupdirect.com had base and clear F3 so I took a chance on it. Turned out decently

 

[72smallairparticler]

Todays progress. Gettin the kids to work.
Got a pushrod measurement of 7.3” - closest ones I see are 7.342 ill order. Also waiting on a hughes order for some shims for the arms

 

[sireland67]

Keep the kids involved, use those idle hands.

 

[72smallairparticler]

Hughes spacers for my rocker arms… wont be buying from the again. Came in a bag that could easily have been oiled to prevent rust. But a little elbow grease and theyll work.

Got the rocker arms installed and prepping my checklist for wrapping up the block. Hopefully ill be dropping the engine back in the car this month.

 

[72smallairparticler]

bye bye 7.25

waiting on hard lines for the 8.8 and some ubolts then I can get that finally installed.

 

[72smallairparticler]

Anyone know if there are “longer than stock” adjuster ball screws for 273 rocker arms? Ran out of thread length getting preload on a few valves

 

[junkyardhero]

Anyone know if there are “longer than stock” adjuster ball screws for 273 rocker arms? Ran out of thread length getting preload on a few valves

sounds like you need longer pushrods...

 

[72smallairparticler]

Yeah I figured that was the case. I have the summit G6420s that measure 7.389 in. Guess ill grab a few at 7.5” or longer.

 

[72smallairparticler]

Things have been slow around here. Busted a finger doing a brake job on my wife's minivan... woof.

Anyway, Nothin' like straddling separate projects. It's the best way to get something done while waiting for parts to ship for another. So while I have pushrods on order, I finally welded up the spring perches on the 8.8 @ ~7degrees pinion angle. I will fine tune the angle once its installed. If you do this project, definitely pull EVERYTHING from the junkyard and don't buy it bare. I am still hunting vent tubes and brake line clips to put all the parts together. Just to get the 8.8 out of the way i'll probably install it and do the rest of the job under the car but man it would be nice to be done already! haha.

More updates to come.

 

[Big.J.007]

Keep at it

 

[junkyardhero]

If you do this project, definitely pull EVERYTHING from the junkyard and don't buy it bare. I am still hunting vent tubes and brake line clips to put all the parts together.

rule number one: take everything at the yard. the bits n' bobs, pins, clips, whatzits, doohickies, dongles, dangles, nuts, bolts, washers, ALL of it.

you don't need it? it goes in the "spares" can to be relegated to the land of misfit hardware-- or as i like to call it: the island of last resorts.

when you need it, it's gold; till then, it's junk.

 

[bjkadron]

Just found this build. Very nice progress! Any chance you know the weight difference between the 7.25 and the 8.8?

 

[72smallairparticler]

Just found this build. Very nice progress! Any chance you know the weight difference between the 7.25 and the 8.8?

Ahh shoot no I dont actually. Id weigh them both but I just sold the axles from the 7.25” the 8.8 is definitely heavier but cant say how much

 

[junkyardhero]

if you need a weight on a 7.25 let me know. somehow i wound up with a pile of them.

you turn your back for two seconds...

 

[bjkadron]

Yeah, I can weigh mine when I get it out, I was just curious if you had measured it.

 

[72smallairparticler]

Got the 8.8 in

Ordered and installed new 7.49" pushrods

Ordered and awaiting radiator, starter, clamps for 8.8 brake line, 8.8 vent and some other small things

Next on the list:

• 8.8 parking cable installation
• Brake lines installation and bleed
• Fill 8.8 with gear oil
  Jump to engine work again
• Set valve lash on the engine
• Install intake
• Install carb
• Fill up torque converter and install
• Mate the trans and engine together
• Install engine mounts

Drop everything in the car

Then the fun continues!

I've been out for vacation, and a bunch of side work to fund the rest of the build so finally good to get some parts on order and get back in the garage here and there.