Search results for query: *

Hello I sold my Dart to a guy in Syracuse NY Is there anybody in the Connecticut area that offers flatbed service? thank you George

For sale is my 73Dart Swinger 440 engine 727 trans, .03 over hemi profile cam. 4:56 rear every part in the front end is new, rebuilt calipers, rebuilt master cylinder, stainless brake lines, plus the line over the rear. Billstein front shocks, steering box rebuilt by firm feel suspension. Ron...

Hello everyone I would like to remove all the rubber hoses that the previous owner used. From the transmission the steel likes are cut and there is rubber fuel line through the header tubes with a heat shield material around it. I was thinking about using an-6 lines from the transmission and...

Hi all is there a place at Carlisle where people from this forum meet? thank you George G

Hello everyone I am looking for a new windshield for my 73 Dart Could anyone recommend where I could get one? thank you George

Hello I needed to replace my water pump (440 engine) as it was leaking. I purchased the Milidon high flow pump My car has no heater core, there was a hose connecting the outlets on the pump housing. When I removed the pump I decided to remove the heater hose nipples and plug them. I noticed...

Hello I have a 73 Dart Swinger is the wheel base 108 or 111 inches? thank you George

Hello everybody Is there a difference in quality of these two pump? thank you George http://www.jegs.com/i/Edelbrock/350/8814/10002/-1 http://www.jegs.com/i/Milodon/697/16260/10002/-1 Which one would you buy

Hello hope everyone had a good 4th I was looking to get some opinions on the Accell 437s plugs. they are currently installed on my 440 Dart these are the short plugs, aka header plugs Appreciate opinions regards George

I finished the rewiring on my Dart, I removed the original dash, and purchased the insert from Redline, popped some holes and installed the Autometer gages. I used the Ron Francis wiring kit. I like the way it was laid out, Each section to be wired is in a separate bag. I started with replacing...

I got a $150 gift certificate to Jegs Im going on their site now!! regards George

Hi Guys I am running new wires to the trunk area for all the lights. I was not able to find sockets with three wires ( one for ground) but a member here suggested I solder a wire to the socket for ground. Please look at the picture this weather tight connector goes in a hole in the trunk, and...

Hey guys I installed these sockets, but they only have 2 wires, one for stop and one for turn signal. there is no ground wire the socket is metal but the housing is a white casted metal, and does not make a good ground. Does anyone know of a 3 wire socket that will fit into a 3/4 inch hole...

Hello I am rewiring the Dart in my spare time. I got the engine running two weeks ago, since then I have been away on business. Today I installed the autometer gages crank it up and the voltmeter showed a steady 14 volts. My question is the turn signal switch connector, has two green wires...

Hi guys I need to replace these sockets as they are rusted in place. Do I have to remove the bumper to get the housing out? I am currently in the process of rewiring the car. I am looking for opinions as to weather I should spray lizard skin on the floor or use the other stick on matts...

Hello all I came across something today, that drove me crazy. I am starting to rewire my Dart, and I have to match up the connectors from the ignition switch to the new system. I was looking at the wiring diagram which I got from my Mopar for the 73 Dart. The ignition terminal on the starter...

Has anyone had any experience with this companies product? http://cgi.ebay.com/ebaymotors/XV-Mopar-Tilt-Steering-Column-A-Body-w-o-Key-_W0QQcmdZViewItemQQhashZitem4cebf71880QQitemZ330376353920QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories#ht_1389wt_941

Hello All could someone please tell me where I can pickup a connector for a 3 prong neutral safety switch? thank you George Gerhard

Hello All This is for the front turn signal on my 73 Dart. The sockets need to be changed. Do they come out of this assembly, or must I replace the whole thing? Where would I get this, I need two thank you George

Hello My 727 seems to be missing the neutral safety switch. It has been 20 years since I removed a 727, but if I remember correct wasn't it drivers side near the trans cooling lines? There seems to be a plug at that place. Appreciate comments thank you George G

Hello I took the wiring out of my Dart today in preparation for my new gages and wiring kit I was hoping to get some suggestions as to what to do with the center section of the dash and the glove box cover, I bought the plastic insert from redline gage works, and I dont want to do something...

It felt good It felt good real good

Hello all Stock mopar electronic distributor. Holding the lower shaft, and turning the rotor I have about 60 degrees of play, what should be normal? thank you George G

Just got my Ron Francis wiring kit, and my new gages. This will be my next project, if I ever get her running right I completely rebuilt the front end. 30 years ago I worked in a front end shop, so I know front ends pretty well. I bought one of the plastic dash replacements from redline...

Hi All I took the Dart out for a ride today to get a wheel alignment. All was good drove on the highway, streets all good Later on I go to get gas and it starts to backfire from the exhaust. Its a 440 with a holley 750 Any ideas??? thank you George

Hello I found this on the MSD website. I am curious about the ready to run distributor for my 440, but I am not sure if it will fit when I change to aftermarket heads in the future. Does anyone have experience with that distributor? thank you George http://www.setyourtiming.com/video.html

Good Morning All I went to Sears today and purchased a new digital timing light for one hundred bucks. I dont know exactly what I should set the timing at. I disconnected the vacuum line from the distributor, set the timing light for 10 degrees and moved the distributor until the crank mark...

Hey All what is a good vacuum advance distributor to use with a MSD 6al box. I noticed some of these distributors are very tall, what do they offer? thank you George G

Hello All Got the Dart back together, and started to drive around a bit. I noticed bad pinging when I would punch the pedal, and it is very rich, to the point I get a headache. 440 engine purple cam. 750 holley (brand new) new plugs Another member on this board will let me borrow his timing...

thinking of purchasing this, but not sure if it will fit my 73 Dart any help would be appreciated thank you George http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=150436357193&ssPageName=ADME:X:RTQ:MOTORS:1123#ht_500wt_956