Search results for query: *

on my 65 valiant/barracuda, is there a replacement transmission crossmember that is already notched out for dual exhaust? one side is notched other flat or does everyone just cut the other side out? any help apprciated.

this might be posted somewhere but no luck on finding it. can some one tell me or point me in right direction on what it takes and what is needed to convert my 65 cuda from non PS to PS? thanks

so i got a kit to convert the front of my 65 cuda to power disk brakes. the one thing i am confused it no matter what i tried the booster and bracket for the shaft that pushes in was hitting the firewall. i called pirate jack where i got the kit and explain. He said oh you have to cut the rod...

do they make the down pipe from the factory manifolds for dual exhaust? i know the trans cross member needs modified though. had some one do it on my 65 cuds and did a terrible job. the driver side turn down from the manifold is way too low for clearance and after very little time all hangers...

so doing a brake job on my 65 valiant/barracuda conversion. rear drum brakes from measurement are 9", ordered new shoes and new drums and new wheel cylinders. when i got them and they all matched up except the wheel cylinders. it took me weeks, but tracked down that it had the 9" shoes, 9" drums...

So my 65 has these rally wheels on it with 215/17/14 on back and 195/75/14 on front. At the time those were the biggest i could fit on it. Well i don't know why, probably from sitting too long the back two tires have separated problem is i cannot find the same size, so is there a different size...

anyone have one of these or know where i can get one?

looking for 65 ish kick down rod for small block 273. i need the slotted rod setup, also any bracket if you have it. let me know what you have and cost thanks.

2002 Monte Carlo SS No it does not run, turns over but can't get it started and battery (side mount) is dead. it will needs towed .. it turns over but battery not strong enough and i don't have another side mount battery. I put a lot of time and money in parts on this i don't have the time...

1987 Ford tempo GL Sedan 4D No it does not run, Yes it will need towed. No i don't know what's wrong with it looks like fuel issues. Yes i have the title. Rare little car. 1987 Ford tempo 4-cyl diesel (mazda) with 5 speed trans. front wheel drive. i bought this off the original owner that...

Looking for a throttle cable setup for my 65 valiant with the 273 commando. its 4 barrel carb . right now it has a demon street carb on it and from a post i did here for help looks like its all messed up. i have no reference to go buy so kinda trying to figure out what will work. this is what is...

I put this demon carb. (1901) on my 273 commando and works great but i cannot get the linkage right. have fabed different brackets, still not right, can't get it to open up all the way. tired of make-shift. do they make a bracket i can just but to make it correct? 1965 valiant conv. 273...

1965 valiant. trying to convert to power disk brakes. i have the rotors, spindles, etc. all on. i tried to just swap out master cylinder and that's not working correctly. Is an 8" setup going to fit in this car. also i'd imagine need to swap out the proportion valve also? needs some guidance...

I had this posted a while back and then had some issues that didn't allow me to finish and completed this transaction. Now that things have leveled out i'd like to sell this setup. *This the best of my knowledge, please ask questions and i'll do my best to answer any questions you have* This is...

Complete 4 speed setup up for barracuda, probably more. I collected the setup to place 4 speed in my 65 barracuda but never going get to it. Other than pedals all should be there. Bellhousing pressure plate clutch even 4 speed indicator plates and floor pan hump. I got it out of a running car...

Looking to try out the 1901 street demon 625 cfm for my 65 barracuda. i think there is way too much carb on it now. it runs like a scalded dog right now but issues with idle and start up, plus its about ready for a rebuild. I been looking around for feedback and haven't see much on the good or...

Looking for a replacement for my 273, wanting electric choke +/- 650 cfm, prefer holley but open for other options. Would like it to be fairly good condition.

Anyone know the color i can get in a rattle can at local store that matches the closest to the dark gray color for the cone ralley caps?

Looking for 1 maybe 2 small bolt pattern ralley wheel center(s). located in arkansas. can come pick up or shipping to zip 72023.

i found this near me. its suppose to be a 71 demon. asking $1800. the stripe throws me. if so woth it? no motor or trans seats in it dont know if correct. spare tire area rotted out. under hoid good

I finally got the disk brake conversion on my 65 cuda. got the wheels from a board member (supposedly off 73 dart ?). Anyway there is 205/70/15 tires mounted on them. No i'm after the trim (beauty) rings and have no idea what size depth wise they are. How can i tell or are they standard size for...

i apologies in advance on the post. i've spent the last couple of hours coming through the post looking for the answer and i'm just not sure. I'm in the middle of typical from drum to disk brake conversion on a 1965 valiant conv. 273 commando. I am using a 73 dart for the reference. everything...

For sale Brand New never been installed Chrysler 273-360 C.I. 8 CYL. 1964-2000 Competition Cam. Solid-Great in 340 & 360 with 9:1 to 9.5:1comp., 650 to 750 CFM carb. and 3.55 to 3.91 gear. Largest cam to use with stock converter. My brother bought this for a project and never used it. located in...

Hi, this is my first drum to brake swap. working on a 65 barracuda. all parts are new and using a 73 dart as my new parts reference. i have read the other posts on this swap and the kelsey disk brake swap. still have a couple of questions that i am not sure of: 1. the bolts that are used to...

Hello, i am in the process of putting disk brakes on my 65 cuda. i have the spindles, rotors , etc. what i am needing from my research is to do this i need to swap out the upper control arms from a newer A-body car. i've been using a 73 dart for reference at the auto parts store. so what i have...

i have a 65 valiant/baracuda clone i'm in process of a disk brake conversion i need 14" rally wheels (2) that will fit disk brakes price and location plz. thanks

Hi, new to forum and got my first a-body. My brother had this car for 10 years and I've always wanted it so I finally got it. its a 65 valiant/barracuda convertible clone. I have a couple of questions to swap out the drum to disk brake conversion. he kept the car pretty original so non-power...