Search results for query: *

Can anyone tell me what a 64 poly engine will use for a bell, flywheel, and what trans will bolt up??

I want to confirm that the #2536563 intake will bolt to 318 heads, it came off 318 but want to confirm it fit without changing the angle of the holes. I assume it was a 273 intake.

'76 smogger 318, 2 bbl. motor, with plenty of miles , I don't think ever apart. Doesn't really smoke, I guess 150,000 mi. Just a driver and fun car. Recommendations for plugs and gap??

I admit to have done mostly BB for decades, then got to mainly playing with slants. BUT..... car in question is this 76 F body roadrunner, original 318 AC car, I ditched the AC and trying to get my belts and pulleys working. I have the OEM 3 groove crank pullet ( car has PS), I have a non...

I admit I should do the search thing, probably 50 pages, but...... unless I find a stock 4 bbl CLOSE BY , what is the recommended dual plane intake for just a low compression 318 cruiser?

I picked p a 76 Volare 318 car, runs drives although I am yet to run down the road. Just got the leaking brake line repaired. The PO had recently put a "gauge type" oil sender on it, and I hooked up an aftermarket gage to it. I admit I always bypass the idiot light and install a mechanical...

I picked up this '72 318 from good buddy, story is it ran good when he got it. I have no doubt what he tells me is true. runs means it ran sitting in the vehicle, idle! been sitting complete, for some years. ? how many. I get it home, it does not...

I need one. can anyone stick one in an envelope and send???? can't find at auto parts store no doubt!

I soaked the pistons and lifters for weeks with everything except skunk pee, finally drove out the pistons, was able to drive the lifters off the cam with a big screwdriver, except ONE lifter. and, I cannot budge the lifters out of the bores. afraid to put...

long story short.. 65 273 2bbl auto cuda.... been piecing this project back together the PO started. he took it ALL apart. story I got from my buddy is that I traded for ...that when he got from the PO was......it had been running car when he started...

is the correct route for the pos. battery cable ( 273) in the 65 cuda...... does it go along the inner fender, then up along firewall under the cowl lip, and then down to the starter???? I have to piece this thing back together and have to get...

I 've been piecing this 54 cuda together since last spring. got the engine/ trans dropped in. I have to bolt in the rocker assembly. I know the specs the FSM gives for adjustment on warm engine. I want to get it close cold. I assume add .002-.003...

wasn't that long ago I looked high and low for the thicker mount for the 273 that went in the 65 cuda. now I need another pair, can't find the thicker ones anywhere or remember where I finally found the other set??? looks like to me the thinner ones I...

did the 65 dart 273 take a thicker or thinner motor mount ???? ( insulator so call it). or does it matter ????? thanks

nutha question!? in the box of parts if got! there are 8 conical washers, enough for the 8 short exh man. bolts. but is that where they go, or do all bolts need the conical washer? or what.!? I have FSM manual, they somehow...

the p o took it apart, I gotta put it back. question: I have complete engine gasket kit, is there a gasket on each end of the hollow bolt. ?? I have what appears to fit inside that is cork and one that fits the outside that's a stiff...

were these solid lifter engines???

273 engine, I got the head bolts soaking in kerosene to make sure they are clean. is that good for lube for them too, or should I blow them dry and wipe a little oil on bottom of bolt? store bought lube??? thanks

I got a 65 cuda, 273 engine, the PO had removed the intake , heads, front of engine..... it sat outside last winter with tarp over it ( or was it piece of plywood??)... was supposedly running engine...... small amount of rust in cylionders, I see some...

help!! i bought my mopar from a young guy that replaced this and that. i see collant leaking from edge where timing cover is at block. i took out the upper bolts on drivers side that hold on power steering pump, and put silicon on those but still see it leaking. i...