Search results for query: *

Here is a full set of stainless steel trim in good condition. Appears to be straight without any dings or dents. Asking $75 plus shipping. Or best offer this is located in Temecula California.

I have a Full passenger side 66–67 commando V8 exterior trim. Peace is in fair condition with a couple dings. Fixable for sure. Asking $25 Plus shipping. Part is located in Temecula California

65 Dart GT recently painted with a fair paint job, 8 3/4 rear end posi 3.23, 71 340 with flowmaster Delta 40s, all new front end bushings and tie rods, alignment done, new windshield, all new brakes and new dual master cylinder. Car runs great, needs tuning and adjustment. Metal is solid. A...

Goodbye.

Not a Mopar but still lots of front end work on the Avenge! 8 year old is still learning to control his 50+ mph RC truck. Hit the curb and destroyed the from end. New skid plate, bumper, yoke, trans case! Whew!

I just recently finished painting the exterior of my Dart. It was the first time I had ever painted a car and I learned a lot. I’m curious with how to go about painting the inside of a car. Is the prep of the metal on the inside as important as the outside? Just thinking about tight spots like...

I just finished my project of installing 5.9 magnum manifolds into my 65 dart running a 340, 904LA automatic floor shift transmission. I did a lot of research on this site, did a lot of trial and error and here is exactly what I used to make these manifolds work in my car. 5.9 magnum manifolds...

I received my steering coupler/U-joint. Steering box side is splined with a set screw. Shaft side is smooth. The end of the shaft still has the pin through it where the old coupler Plunges/engages. I was thinking of notching the new coupler to receive the pin on either side of the shaft. There...

I have four pulleys for sale The following part numbers: 3640851-$25 3614382-$20 3614378-$50 And a single crank pulley with no number. stamped with the letter “S“ on it. $20 all pulleys are plus shipping. Located in Temecula, CA

Hey guys, I’m taking a step back and looking at my overall financial situation. I’ve had 2 project cars with The Main being my 69 super bee then I picked up a 65 Dart GT a few years back. I am considering selling the 65 Dart GT. I’m not sure how the market is right now for resale so I’m trying...

I purchased this adapter to go between my manual steering box and my power steering coupler. However, because of the 5.9 magnum manifolds using this adapter does not work. Paid $128 for it. I’m asking $100 plus shipping. It’s new and never installed. I am in Temecula, CA

Looking at two different couplers/universal joints from Borgeson. Trying to go between my manual steering box which is 36 spline and .72 inches diameter and my power steering shaft which is smooth and .75 inches diameter. Will these work? Is one better than the other?

Was at a friends house and he said his neighbor is trying to give this away. Looks straight and in good condition from the outside. My friend says it turns over but won’t run and the inside has Definitely been used. We’ve been wanting a camper just don’t want to get into another money pit. I...

As I’m putting in my new exhaust I wanted to ask in advance if there’s anything specific I should look out for. This is definitely a custom/make it work kind of exhaust. Looking at how the pipes are coming down from the manifolds. they run pretty close to the torsion bars as well as my...

Hey guys I know this is the a body site but, a guy by the name of Randy Carlson who is out here in Southern California just made a big score. Picked up five cars in Arizona. A 426 hemi four-speed challenger, charger 500, charger RT, super B, and a Mustang GT500 KR. All cars are being brought...

Modifying my tranny mount to fit my dual exhaust.

So I’ve been driving a 2012 Volkswagen golf diesel manual for a few years. It was certified preowned. Recently the engine lost power and I took it to the shop. You guessed it! High pressure fuel pump is out and to replace everything is like $6000. I only owe 12 on it. I think instead of fixing...

Does anyone know the measurement of the power steering shaft for a 65 dart? I wanted to buy an extra piece of stock so I can lengthen mine

So I started working on getting the driver side magnum 5.9 manifold in place. First thing I had to do was switch from a power steering to a manual steering box. Got that done! Then I had to grind a little bit of the top of the steering box and the bottom of the manifold to make it fit. since I...

Hey guys, finally got the steering box unbolted and the studs out so I can remove it. Doesn’t seem to want to come out the top. If I remove the starter will it slip out through the bottom? or do I have to unbolt the driver side engine mount and lift the engine up?

Does anyone know if a steering wheel from a 72 duster will fit a 65 Dart steering shaft?

I didn’t see a specific location for WTB items. I’m looking for a manual steering box for a 65 dart. Preferably something that is working but if not at least something that has all the parts that I can rebuild.

I’ve never had a power steering pump in my car and I’ve always thought that it was manual. I’m trying to put in my magnum manifolds and saw this piece on top of my steering box that looks like it would circulate fluid. If this is power steering is it possible to just remove that top piece and...

I’m coming back around to this topic. I’m running a 340 in my 1965 dart. My question is how do I choose a radiator? Seeing that the engine is Mis-matched with the car. currently my lower radiator hose comes out on the passenger side and hooks up to the passenger side. Also the current radiator I...

OK so I finally picked up my 5.9 magnum manifolds. Just looking at them and the car now. My first thought is I’m going to have to reposition the oil filter which is currently on the 90° adapter. I’m assuming I can just flip the adapter around 180 deg the other way so it’s pointing towards the...

At a local salvage yard.

I’ve been trying to find a set of 5.9 magnum manifolds to go on my 340 and into my 65 Dart. I found a pair however the yard wants $65 apiece for them. That seems high since I found another member who lives about an hour and a half or two hours north of me who said I could have them for $20...

Finally finished the paint job. Lots of color sanding to do. I made one big mistake by forgetting to put plastic over the back wheels. I’ll deal with that later.

Started this project of painting the 65 Dart over the last few weeks. Put up a paint booth in my garage. This is the first car I’ve ever painted. It’s been a great learning experience. I’m almost done! I only have the rear quarter panels and trunk lid to paint. Decided to go with a blacked out...

Trying to decide on exhaust for my 340. I put it in my Dart which was originally at 273 and has a 2 to 1 pipe. I was thinking about just cutting off the 2 to 1 and extending the pipes back with mufflers. Then I started reading about X pipes and Y pipes and how those assist with exhaust. If I...